Free models · Game-ready GLB
Assets
Every model here is a game-ready GLB that drops into three.js, Blender, Godot, Unity and Unreal, free to use in personal and commercial work without crediting anyone.
Files are binary glTF with embedded WebP textures and quantized geometry, which three.js reads natively and Blender, Godot and Unity import as they are, so nothing needs a Draco or KTX2 decoder. Each asset page carries a permanent CDN URL you can load straight from your code.
18,677 free GLB models
Front of House Mixing Desk (Live Music Venue and Festival Stage)
A digital front of house desk on its flight case base: a 32 fader surface with a bank of rotaries and a raked screen, at standing height on a cased plinth. The operator side faces +Z.
Lighting Bar with PAR Cans (Live Music Venue and Festival Stage)
A 2 m lighting bar with four PAR cans on it: hook clamps at both ends, alternating tilts down the bar and a coloured gel frame on the front of every can, in magenta, amber, blue and green.
Stage Monitor Wedge (Live Music Venue and Festival Stage)
A 12 inch floor monitor: a 45 degree wedge on rubber runners with a perforated grille over the coaxial driver, for the line of wedges along the downstage edge.
Subwoofer Cabinet (Live Music Venue and Festival Stage)
A double 18 inch bandpass subwoofer: a 1.2 m birch enclosure on skid runners with two tuned ports through the baffle, a grille over the mouth and a recessed connector plate on the back.
Line Array Hang, Ten Boxes (Live Music Venue and Festival Stage)
A flown line array: ten boxes under a fly bar, splayed from level at the top to 34 degrees down at the bottom so the column curves the way a real hang does. About 3.6 m of array under the bar.
Line Array Ground Stack, Six Boxes (Live Music Venue and Festival Stage)
A ground stacked array: six boxes on a raked stack frame, the bottom box aimed up into the crowd and the splay closing toward the top. About 2.3 m of array on the frame.
PA Stack Frame (Live Music Venue and Festival Stage)
A wheeled stacking frame for a ground stacked PA: a welded dolly with raked bearers that tilt the bottom box up into the crowd, four braked castors and lifting points at both ends.
Line Array Speaker Cabinet (Live Music Venue and Festival Stage)
A three way line array box: a 1.05 m wedge shaped enclosure with a horn section between two cone sections behind a steel grille, rigging ears on both side walls and pin holes for the splay link.
Crowd Barrier Section (Live Music Venue and Festival Stage)
A 2 m front of house crowd barrier: a welded steel frame with three crowd rails, a stepped foot plate for the security team to stand on and a toe plate along the crowd side.
LED Wall Panel Module (Live Music Venue and Festival Stage)
A 1 m square LED video panel: an emissive face in a cast frame with locks on both stiles and a rear rigging bar. Tile it on a 1 m grid for a backdrop wall or a side screen of any size.
Backdrop Banner Frame (Live Music Venue and Festival Stage)
A 3 by 3.2 m banner frame: a tube frame on raked back legs with ballast pads, carrying a printed PVC banner and a light panel across it. Frames butt into a sponsor wall along a pit or a walkway.
AnimatedCrowd Barrier Gate (Live Music Venue and Festival Stage)
A 2 m crowd barrier with a side hung gate leaf in it: the same welded frame and foot plate with an amber leaf on two hinge rings and a drop bolt, for the pit access point in a front of house barrier run.
Stage Roof Canopy Section, Short Bay (Live Music Venue and Festival Stage)
A 3 by 3.3 m festival roof section, the short bay for a front of house or mixer tent: the same arched sheeting and purlins on a 3 m module with a printed valance on its downstage edge.
Wind Wall Scrim Panel (Live Music Venue and Festival Stage)
A 3 by 4 m wind wall: a perforated scrim stretched in an alloy frame with tie rings down both stiles. Runs of it close the sides of a festival stage without taking the wind load of a solid wall.
Stage Roof Canopy Section (Live Music Venue and Festival Stage)
A 3 by 6.3 m festival roof section: arched PVC sheeting on three purlins and two edge rails, with a printed valance on its downstage edge. Sections butt on a 3 m module to roof a stage of any width.
Ground Support Base Plate (Live Music Venue and Festival Stage)
A 900 mm steel base plate for a truss tower: a spigot receiver on a levelled plate with four adjusting feet and a pair of ballast weights on it. The tower spigots into the top at 100 mm.
Truss Corner Block (Live Music Venue and Festival Stage)
A 90 degree box truss corner: a 290 mm cube with a spigot arm on the -X face and another on the +Z face, and a base plate under it that lands on a vertical tower. Four rotations of it close a rectangular roof grid.
Stage Step Unit (Live Music Venue and Festival Stage)
A four tread stage stair rising 1 m to deck height, 1.2 m wide with a scaffold handrail either side. The top tread stands against the stage edge; the treads are the same non slip ply as the decking.
Truss Straight Bay (Live Music Venue and Festival Stage)
A 3 m bay of 290 mm square box truss: four chords on a zigzag brace with spigot plates at both ends. The horizontal building block of a roof, a header or a ground support run.
Truss Vertical Tower (Live Music Venue and Festival Stage)
A 3 m vertical tower section in the same 290 mm box truss, spigoted top and bottom. Stack two on a base plate for a 6 m ground support leg under a festival roof.
Stage Deck Module (Live Music Venue and Festival Stage)
A 2 by 1 m stage deck on 1 m legs: a non slip ply top on a welded frame with four sleeved legs and levelling feet. Repeat it on the 2 by 1 m grid to build a stage of any size.
Festival Field Ground Tile, Worn Track (Live Music Venue and Festival Stage)
A 4 m worn ground tile: the same field module rutted down to bare earth with two wheel tracks through it and grass surviving in patches at the edges, for the walkways, the vehicle route and the trodden ground in front of a stage.
Festival Field Ground Tile (Live Music Venue and Festival Stage)
A 4 m festival field tile: trodden grass on a broken surface, with bare dry patches through the turf and tufts standing proud of it. Tile it on a 4 m grid, which is a whole number of stage deck modules, to lay the ground a whole site stands on.
Stage Riser Block (Live Music Venue and Festival Stage)
A 1 m square riser 400 mm high: a ply top on a folding frame, for lifting a backline amplifier, a keyboard rig or a side fill off the deck.