Free models · CC0
Realistic
Every realistic model below is a self-contained .glb under 5 MB, released under CC0 1.0 so it can be used and modified in commercial projects without attribution.
Load one straight from its CDN URL with a plain GLTFLoader, or take a whole themed set from the packs.
4,440 free GLB models
Route connector cases (Mountaineering and Summit Expedition)
Composed example for Mountaineering and Summit Expedition.
Icefall crossing (Mountaineering and Summit Expedition)
Composed example for Mountaineering and Summit Expedition.
Bergschrund lip (Mountaineering and Summit Expedition)
Four-metre section where the glacier pulls away from the headwall, leaving an open gap under a two-metre ice lip.
Base camp on moraine (Mountaineering and Summit Expedition)
Composed example for Mountaineering and Summit Expedition.
Summit ridge (Mountaineering and Summit Expedition)
Composed example for Mountaineering and Summit Expedition.
Rock band step (Mountaineering and Summit Expedition)
Four-metre wide rock step with a 1.7 m rise, a broken ledge above, a snow gully at the foot and a fixed line.
Crevasse module (Mountaineering and Summit Expedition)
Four-metre glacier section split by a steep-walled crevasse with a blue ice throat and a snow bridge remnant.
Summit cairn (Mountaineering and Summit Expedition)
Stacked stone summit cairn about 1.2 m high with a wand and two strips of marker tape.
Moraine ground tile (Mountaineering and Summit Expedition)
Four-metre square moraine tile of loose rubble over glacier ice, the surface base camp is levelled on.
Serac block (Mountaineering and Summit Expedition)
Leaning three-metre tower of fractured glacier ice with a wind-loaded cap and collapsed blocks at the foot.
Snow ridge module (Mountaineering and Summit Expedition)
Four-metre snow arete section with a rising crest, exposed rock on the windward flank and a kicked boot track.
Stove and pot set (Mountaineering and Summit Expedition)
Gas cartridge stove with pot supports, a wide pot and lid, a wrapped windscreen and a spare cartridge.
Corniced ridge module (Mountaineering and Summit Expedition)
Four-metre ridge section with a wind-built cornice overhanging the lee side and a fracture line at the crown.
Glacier goggles (Mountaineering and Summit Expedition)
Wide cylindrical-lens goggles in a foam-backed frame with an elasticated strap laid out behind.
High-altitude double boots (Mountaineering and Summit Expedition)
Pair of double boots with integral gaiters, front zips, lace hooks and welts for crampon bails.
Summit pack (Mountaineering and Summit Expedition)
Thirty litre lidless summit pack on the same back system, stripped for a summit day.
Climbing harness with rack (Mountaineering and Summit Expedition)
Padded sit harness on a stand, with four gear loops carrying karabiners, slings and a belay device.
Oxygen mask and regulator (Mountaineering and Summit Expedition)
Oro-nasal mask with an exhalation port and reservoir, on a corrugated hose to a regulator block.
Expedition pack (Mountaineering and Summit Expedition)
Seventy-five litre expedition pack with a lid, hip belt, compression straps, axe loops and a strapped rope.
Oxygen cylinder (Mountaineering and Summit Expedition)
Filament-wound oxygen cylinder with a neck valve, gauge, carry ring and a protective cage.
Climbing helmet (Mountaineering and Summit Expedition)
Hybrid shell climbing helmet with side vents, headlamp clips and an adjustable chin harness.
Twelve-point crampons, pair (Mountaineering and Summit Expedition)
Pair of step-in twelve-point crampons with front points, toe bail, heel lever and retaining straps.
Technical ice tools, pair (Mountaineering and Summit Expedition)
Matched pair of bent-shaft technical tools, one with a hammer and one with an adze, with grip rests.
Coiled climbing rope (Mountaineering and Summit Expedition)
Sixty-metre single rope flaked into a butterfly coil, waist-wrapped and tied off with two tails.