3D Assets
@3dassets
Hinged hatch cover (Space Station and Docking Bays)
A 2 m hatch cover assembly: a bolted seat ring with a sealed face and six latch blocks, and a domed insulated cover swung fully open on a named hinge node carried by two support links.
Transfer tunnel with hatch (Space Station and Docking Bays)
A 2 m square-section transfer vestibule with a clear 1.7 m bore between two hatch ports, a 1.5 m swing hatch standing open on a named hinge node with a viewing pane, interior rails and a wall control panel.
Docking target cross (Space Station and Docking Bays)
A 0.9 m docking alignment target: a bolted base plate on four braces carrying a framed board with a raised black cross and ring, and a centre standoff pin with a yellow cap for the approach camera.
Common berthing mechanism (Space Station and Docking Bays)
A 2.5 m passive berthing ring: a bolted flange with sixteen powered bolts, four capture latch housings with their striker plates, four alignment guides and a sealed hatch face.
Androgynous docking port (Space Station and Docking Bays)
A 2.1 m androgynous docking mechanism: a bolted base flange with a station hatch port at the rear, an active capture ring with three guide petals, four latch housings and a target patch.
Extended soft capture ring (Space Station and Docking Bays)
A 2 m soft capture ring shown extended on six linear actuators: a fixed base flange, telescoping struts with damper bodies, the capture ring with a yellow contact band and three alignment blocks.
EVA handrail run (Space Station and Docking Bays)
A 2.2 m external handrail run on a mounting strip: two yellow translation rails on machined standoffs, a base plate with a blanket patch and a marked worksite label.
External stowage platform (Space Station and Docking Bays)
A 3.2 by 2 m external stowage platform: a slatted deck on standoffs, four spare orbital replacement units under tie-down straps, a side bracket with a truss port, a grapple fixture and an EVA rail.
Truss rotary joint (Space Station and Docking Bays)
A 2.7 m truss rotary joint: two short truss stubs, fixed race housings and a 3 m drive ring with twelve trundle bearing blocks on a named rotating node, plus a routed power line.
Stowed radiator panel array (Space Station and Docking Bays)
The radiator retracted for launch or safing, with the three panels folded into a parallel stack on their hinge nodes above the pump bracket.
Deployed radiator panel array (Space Station and Docking Bays)
A deployed thermal radiator: a pump and rotary bracket on a truss port, a spine beam and three 3.4 by 2.6 m panels fanned on named hinge nodes with fluid line ribs.
Stowed solar array canister (Space Station and Docking Bays)
A 4.1 m launch-stowed array canister: the same rotating base, a mast canister and two folded blanket boxes clamped either side with yellow release latches and a grapple fixture.
Short connecting tunnel (Space Station and Docking Bays)
A 2.7 m pressurised connecting tunnel with hatch ports at both ends, a convoluted bellows mid-section, four external stiffener rods and translation rails on all four faces.
Deployed solar array wing (Space Station and Docking Bays)
An 11.5 m deployed photovoltaic wing: a rotating base canister on a named gimbal node, a lattice mast and two 9.2 by 3.3 m blankets with cell strips, edge battens and a tensioning bar.
Truss end cap (Space Station and Docking Bays)
A 2 m closed truss end: half bay, a plated bulkhead with four fluid couplings, an avionics box, a low-gain antenna mast and one truss port so a run can be terminated.
Truss bay segment with utilities (Space Station and Docking Bays)
The truss bay carrying a full utility fit: two orbital replacement unit boxes with gold covers and a routed fluid line loop between the longerons.
Truss bay segment (Space Station and Docking Bays)
A 4 m aluminium truss bay on a 2.4 m square section: four longerons, ribbed bulkhead frames, cross bracing, corner end fittings, a utility box, an EVA rail and a grapple fixture.
Service module with tankage (Space Station and Docking Bays)
A 7.4 m service module: forward hatch port, four external spherical propellant tanks on struts, a main engine bell, two reaction control pods and a nadir body radiator.
Expandable soft-goods habitat (Space Station and Docking Bays)
A 7.8 m expandable habitat: a lofted soft-goods shell scalloped by eight longitudinal restraint straps, rigid metal end bulkheads, an aft hatch port, four hoop straps and a grapple fixture.
Crew airlock module (Space Station and Docking Bays)
A 4.7 m crew airlock, 6.0 m overall with the hatch open: aft hatch to the station, a 1.4 m forward EVA hatch swung open on a named hinge node, two external high-pressure gas tanks, a nadir depress pump box and dense translation rails.
Cargo logistics module (Space Station and Docking Bays)
A 6.7 m pressurised logistics module: one forward berthing hatch, a blanked conical aft service section with four reaction control pods and two gas tanks, a deployed antenna and a grapple fixture.
Crew habitation module, gold blanket (Space Station and Docking Bays)
The habitation module finished with gold multi-layer insulation over the mid-section and dark stowage racks, for stations that mix blanket liveries across their pressurised elements.
Compact laboratory module (Space Station and Docking Bays)
A 7.2 m short-body laboratory module on the same hatch grid, with one pair of experiment canisters, a shorter radiator and fewer rail runs for tight station layouts.
Four-port station node (Space Station and Docking Bays)
A 3.6 m pressurised connecting node with forward, aft, port and starboard hatch ports on machined stubs, a zenith avionics box, grapple fixture, low-gain antenna and EVA translation rails.