Free models · Game-ready GLB
Roads infrastructure
Every realistic roads infrastructure below is a self-contained .glb under 25 MB that drops into three.js, Blender, Godot, Unity and Unreal, free to use and modify in commercial projects without attribution.
Load one straight from its CDN URL with a plain GLTFLoader, or take a whole roads infrastructure set from the packs.
611 free GLB models
Deluge Pipe Elbow (Rocket Launch Pad and Gantry)
The deluge main turning a right angle on the same 8 m module: a north port and a west port meeting at a swept bend on its saddles, so the water main can follow the pad boundary.
Water Deluge Head (Rocket Launch Pad and Gantry)
A 6.7 m deluge head: a mast on a concrete footing carrying a spray ring of eight nozzle arms, with the feed pipe coming in at ground level through a valve block and a ladder up the mast. Sprays are not modelled.
AnimatedLaunch Mount with Clamps (Rocket Launch Pad and Gantry)
The launch mount: a ring deck 11.5 m across on six columns over the trench mouth, railed all round, with a yellow kick ring for the vehicle skirt and four hold down clamps on hinge posts that swing clear at release. Umbilical plate and cryogenic risers on one flank.
Flame Deflector (Rocket Launch Pad and Gantry)
A steel framed double wedge deflector, 3.4 m wide and 2.8 m tall, that splits the exhaust plume down both arms of the trench. Ablative dark face, a bolted cradle underneath and a cooling water manifold along each flank.
Launch Table (Rocket Launch Pad and Gantry)
A 7.2 m steel launch table for a small vehicle: four jack posts on pads, a bolted deck frame with an open flame hole, a railed working deck, an access stair and a blank hazard plate on the front girder.
Flame Trench Section (Rocket Launch Pad and Gantry)
An 8 m section of flame trench: two 2.6 m concrete walls with a coping lip and a scorched lining, a sloped channel floor 3.4 m across, a drain sump and deluge nozzles along both kerbs. Ported at both ends so the trench runs as far as the pad needs.
Hardstand Module (Rocket Launch Pad and Gantry)
An 8 m hardstand module for parking transporters, carts and skids beside the pad: a gravel bed, a laid concrete deck with joint lines and a yellow kerb down each side. Ported on all four edges to the same grid as the apron.
Pad Apron Module (Rocket Launch Pad and Gantry)
An 8 m square reinforced concrete pad apron module, 180 mm thick, with cast joint strips, a central drain channel and four bolt groups. Edge ported north, south, east and west so an apron of any size tiles out of repeats.
Scorched Apron Module (Rocket Launch Pad and Gantry)
The pad apron module in flame washed dark concrete, with soot patches where the exhaust plume has swept the slab. Same 8 m module and the same four edge ports, so it drops straight into an apron built from the clean tiles.
Water Channel Runnel (Desert Mosque and Madrasa Courtyard)
Free 3D model of a 3 m water channel and runnel module for a desert mosque courtyard: a tiled cut with dressed kerbs, a still water surface and a stop at each joint.
Courtyard Paving Module (Desert Mosque and Madrasa Courtyard)
Free 3D model of a 3 m courtyard paving module for a desert mosque or madrasa kit: sixteen dressed flags in two stones on a bedding course.
Stepping Stone Path (Korean Hanok Village and Street)
A 3 m run of flat stepping stones bedded in earth with moss between them, the way across a yard or a wet corner.
Ondol Flue Run (Korean Hanok Village and Street)
A 3 m run of underfloor flue: a clay duct on a stone bed with removable cover slabs over it, the heat path from the firebox to the chimney.
Stepped Lane Module (Korean Hanok Village and Street)
A 3 m wide flight of four shallow stone steps with a rubble kerb each side, the way a village lane climbs a slope.
Stone Street Module (Korean Hanok Village and Street)
A 3 m square of village street laid in irregular stone setts on an earth bed, with the joints left open between them.
Courtyard Ground Module (Korean Hanok Village and Street)
A 3 m square of beaten earth madang, the swept yard a hanok stands round, with a few small stones bedded in the surface.
Yard floodlight mast, 12 m (Shipyard and Dry Dock)
Lattice floodlight mast 12 m to the head frame on a bolted concrete base, carrying six blank faced floodlights on a raked bracket, with a climbing ladder, a cable box at the foot and a yellow banded lower section.
Quay edge slab, 4 m (Shipyard and Dry Dock)
Quay coping slab 4 m square with a galvanised edge angle over the water, a yellow safety line set back from the lip and two recessed tie down pockets. Ports at both ends so a quay runs to any length.
Slipway section with keel ways, 4 m (Shipyard and Dry Dock)
Concrete slipway bay 4 m square falling 0.35 m across its length, with two greased timber keel ways, a side kerb and a cast anchor eye, for running a cradle down to the water. Ports at both ends so a slipway runs to the waterline.
Dry dock altar wall section, 4 m (Shipyard and Dry Dock)
Stepped dock wall 4 m long and 6 m tall: four concrete altars a shore can be set on, a galvanised lip angle at the coping, a yellow edge line and a recessed rung ladder. Ports at both ends so a dock side runs to any length.
Dry dock access stair tower (Shipyard and Dry Dock)
Bolted steel stair tower 6 m tall with two flights, a half landing and a top landing at dock level, yellow topped handrails throughout and a kick plate, for getting down the altar wall of a graving dock on foot.
AnimatedDock gate caisson, 16 m (Shipyard and Dry Dock)
Steel dock gate closing a 16 m graving dock: a plated box caisson on a concrete quoin, with vertical stiffeners, timber seating faces, flooding valve wheels and a railed walkway across its top. The leaf swings off the quoin to open the dock.
Yard apron slab, 4 m (Shipyard and Dry Dock)
Heavy duty concrete apron slab 4 m square with a recessed movement joint and a cast in tie down pocket, for the dock side a shipyard works from. Ports on all four edges so an apron tiles to any size.
Graving dock floor tile, 4 m (Shipyard and Dry Dock)
Dock bottom slab 4 m square and 0.2 m thick with a drainage channel down one edge and a cast grating over the culvert, for the floor of a graving dock. Ports on all four edges so a dock floor runs to any length.