3D Assets
@3dassets
AnimatedFolding Kick Scooter (Skate Park and Street Sports)
A stunt kick scooter with a low charcoal deck, grip plate, teal steering column, foam grips, a rear fender brake and two wheels on their own axle nodes.
AnimatedBMX Park Bike (Skate Park and Street Sports)
A 20 inch BMX: teal tubular frame, four peg axles, riser bars with grips, a slim saddle and two wheels on their own axle nodes. The chain and the drivetrain are modelled as a solid sprocket and do not turn.
AnimatedSkateboard with Teal Wheels (Skate Park and Street Sports)
The complete skateboard with a yellow underside print and teal wheels. Geometry is unchanged.
AnimatedSkateboard with Sunset Graphic (Skate Park and Street Sports)
The complete skateboard with an orange underside print and matching wheels. Geometry is unchanged.
AnimatedSkateboard Resting Deck Down (Skate Park and Street Sports)
The same complete rolled over and resting on its grip tape with the wheels in the air, the way a board is left beside a ledge. Wheels stay separate nodes.
Bowl Corner Wall Section (Skate Park and Street Sports)
A quarter turn of the same bowl wall inside a 3.0 x 3.0 m square, swept about a 1.2 m inner radius. Its two end ports meet straight sections, so four corners and any number of straights close a bowl.
AnimatedComplete Skateboard (Skate Park and Street Sports)
A 81 cm complete: maple deck with a kicked nose and tail, gripped top, printed underside, two trucks and four urethane wheels on their own axle nodes.
Bowl Coping Edge Piece (Skate Park and Street Sports)
A 4 m coping run: a steel coping pipe bedded on a thin painted fillet, sized to the bowl wall deck lip. Its seat port drops onto a bowl straight section's coping port.
Bowl Straight Wall Section (Skate Park and Street Sports)
A 4 m run of bowl wall: a 1.5 m transition from the floor to vertical with a 0.3 m deck lip. End ports chain straights and corners into a closed bowl and the coping port takes the coping edge piece. Sink the ring for a below grade bowl.
Five Step Concrete Stair Set (Skate Park and Street Sports)
The same stair run five risers deep, 0.90 m down to the pad: the street set that a handrail and a five stair gap are built around.
Street Stair Handrail (Skate Park and Street Sports)
A 1.84 m round steel handrail on two footed posts, pitched to the five step stair set. The foot port drops on the pad and the head port on the top landing.
Three Step Concrete Stair Set (Skate Park and Street Sports)
A 2.4 m wide poured stair of three 180 mm risers and 320 mm goings with a 0.5 m top landing and painted nosings. The top port meets a raised pad edge and the rail ports take the matching handrail.
Kinked Grind Rail (Skate Park and Street Sports)
A 3 m round steel rail that kinks up at both ends, the street handrail shape, on two splayed painted A frames.
Flat Grind Rail (Skate Park and Street Sports)
A 3 m round steel grind rail 0.4 m above the ground on two splayed painted A frames with bolted footplates.
Steel Edged Grind Box (Skate Park and Street Sports)
A 2.4 x 0.55 m concrete grind box 0.45 m tall with chamfered top corners, a steel angle capping each grinding edge and a painted band down each side.
Concrete Ledge Block (Skate Park and Street Sports)
A 1.6 x 0.6 m precast ledge 0.4 m tall with one chamfered grinding edge and a sprayed paint band on the face. Drops straight onto the pad.
Funbox with Grind Rail (Skate Park and Street Sports)
The funbox with a 3.4 m steel grind rail standing 0.3 m above its deck on two posts. Same footprint and the same end ports.
Concrete Funbox (Skate Park and Street Sports)
A 4 m wide funbox: a 2.8 m flat deck 0.6 m up with a bank at each end and painted steel edging on both top lips. Boxes butt end to end along the 4 m grid.
Portable Launch Ramp (Skate Park and Street Sports)
A 1.2 m wide kicker 0.5 m tall over a 1.5 m run, with a curved face and a steel lip bar. Small enough to carry out and drop anywhere on the pad.
Concrete Bank Ramp (Skate Park and Street Sports)
A 4 m wide flat bank rising 0.9 m over a 3 m run, with a painted top edge and a 1 m deck. 4 m front to back, so the deck meets a raised pad block on the 4 m grid; the pad port sits on the low edge.
Half Pipe Mini Ramp Section (Skate Park and Street Sports)
A 4 m wide section of a 1.4 m mini ramp: two facing transitions on a poured floor slab, a 2.4 m flat bottom, coping pipes on both lips and 0.4 m decks. Sections butt end to end to make a ramp of any width.
Flat Concrete Ground Tile (Skate Park and Street Sports)
A 4 x 4 m poured concrete pad tile, 150 mm thick, with two shallow saw cut joints across it. Tiles butt edge to edge on the 4 m grid to lay a skate park floor of any size.
Concrete Quarter Pipe Ramp (Skate Park and Street Sports)
A 4 m wide quarter pipe with a 1.6 m transition, a steel coping pipe on the lip and a 0.7 m deck behind it. Rides toward -Z; the pad port sits on the front edge on the 4 m grid.
Raised Pad Block (Skate Park and Street Sports)
A 4 x 4 m concrete plinth 0.9 m tall with a proud capping slab and a painted edge band, the raised plaza a street stair set drops off. Blocks tile on the 4 m grid and the top ports take a stair set.