3D Assets
@3dassets
Glue and finish shelving, 0.9 m (Woodworking Workshop and Joinery)
Steel shelving unit 0.9 m wide and 1.5 m tall with three shelves of workshop stock: tins of finish and stain, glue bottles, a jar of brushes, rag rolls and a measuring jug, all with blank labels.
Panelled door on a stand, 2 m (Woodworking Workshop and Joinery)
Finished four panel door 2 m tall in hardwood with raised ply panels, a steel lever handle and two hinges, standing upright in a timber stand with a back brace, the way a finished job waits for collection.
Timber rack with boards, 2.3 m (Woodworking Workshop and Joinery)
Blue cantilever timber rack 2.3 m wide and 2.25 m tall on bolted foot plates, with four pairs of raked arms carrying a full load of sawn hardwood and softwood boards in mixed widths and thicknesses.
Sheet material rack with ply, 2.5 m (Woodworking Workshop and Joinery)
Upright sheet rack 2.5 m wide: a steel base frame with charcoal dividers and a back leaning post, holding five birch ply and MDF sheets on edge with their faces clear of the floor.
Timber rack, part loaded, 2.3 m (Woodworking Workshop and Joinery)
The same cantilever rack after a run of work: the lower arms still carrying boards and the upper arms nearly clear, for a shop that has been using its stock.
Sharpening station, 0.7 m (Woodworking Workshop and Joinery)
Sharpening bench in pine: a charcoal stone pond holding a coarse and a fine waterstone, a leather strop on its block, a honing guide, a water jug and a lower shelf of stone boxes, set at the height a joiner touches up an iron.
Bench plane, 360 mm (Woodworking Workshop and Joinery)
Number five jack plane: a flat steel sole, a blue japanned body, the iron and red lever cap set at the mouth, a timber tote and front knob, sitting on its sole the way it is left on the bench.
Mallet and chisel set on a tray, 0.5 m (Woodworking Workshop and Joinery)
A joiner's mallet standing in a shallow pine tray with three bench chisels laid beside it and a marking gauge: handles, ferrules and ground bevels modelled, for dressing a bench or an assembly table mid job.
Clamp rack with sash clamps, 1.8 m (Woodworking Workshop and Joinery)
Steel A frame clamp rack on castors holding six 1.5 m sash clamps: each clamp is a steel bar with a red head casting, a sliding tail on its pin and a screw with a timber T handle, racked the way a shop keeps them beside the assembly table.
AnimatedRolling tool chest, 1 m (Woodworking Workshop and Joinery)
Red seven drawer tool chest on four castors: a timber worktop, steel drawer pulls on every front, a side handle and a lower cupboard, with every drawer opening on its runners.
Sawhorse pair, 1 m (Woodworking Workshop and Joinery)
Two site built timber sawhorses with 1 m top beams, splayed legs, gussets and a lower tie, set out as a pair at working distance so a board or a door can be laid across them.
Tool wall panel with hand tools, 1.6 m (Woodworking Workshop and Joinery)
Wall hung tool board 1.6 m by 1 m: a pale ply panel in a timber frame, carrying four bench chisels on their rack, a tenon saw on its pegs, a bench plane on its shelf, two try squares, a mallet and two F clamps, each tool modelled as the real thing.
AnimatedJoiner's workbench with vice, 2 m (Woodworking Workshop and Joinery)
Laminated hardwood bench 2 m long on square legs and stretchers: eight glued top boards with a row of round dog holes, a front apron, a lower pine shelf and a cast front vice whose timber faced jaw slides out on its screw.
Assembly table, 1.8 m (Woodworking Workshop and Joinery)
Low assembly table 1.8 m by 1.1 m on a blue welded frame: a birch ply top on a torsion box grid with a field of dog holes, a lower shelf carrying two clamps and adjustable feet, built at 800 mm so a carcass can be squared up on it.
AnimatedMobile machine base, 0.8 m (Woodworking Workshop and Joinery)
Adjustable steel machine base: a welded rectangular frame with four corner brackets, a yellow foot lever and four castor wheels, so a planer or a band saw can be rolled out of the way and set down again.
AnimatedRouter table, 0.95 m (Woodworking Workshop and Joinery)
Enclosed router table: a blue cabinet with a cream laminated top and a steel insert plate, a split charcoal fence with its dust port and guard, a start and stop station on the front, and the router cutter turning in the opening.
AnimatedWood lathe with tool rest, 1.9 m (Woodworking Workshop and Joinery)
Cast bed lathe on two green pedestals: twin steel ways, a headstock with the drive spindle, a tailstock on its quill, a charcoal banjo carrying the steel tool rest and a turned blank between centres that spins with the spindle.
AnimatedTwin bag dust extractor, 2.05 m (Woodworking Workshop and Joinery)
Blue twin bag extractor on a charcoal base with four castors: a fan housing over the motor, a 200 mm inlet with its flexible cuff, a steel hoop frame carrying the cream filter bag above and the collection bag below, and the motor fan turning on top.
AnimatedDisc and belt sander on a stand, 1.2 m (Woodworking Workshop and Joinery)
Blue bench sander on a grey steel stand: a 300 mm cream sanding disc behind its charcoal guard with a tilting steel table, a tilting belt platen on the left with its drums, a dust port under each and a start and stop station.
AnimatedFloor standing pillar drill, 1.85 m (Woodworking Workshop and Joinery)
Cast base, a 1.6 m steel column, an adjustable table on its bracket and a grey head with a red belt cover: the quill feeds down on its three ball handles and the chuck and drill bit turn with it.
AnimatedSpindle moulder, 1.1 m (Woodworking Workshop and Joinery)
Green spindle moulder: a cast table with its insert ring over a closed cabinet, a split cream fence on a charcoal body, a yellow ring guard, the rise and fall handwheel and a start and stop station, with the spindle and its cutter block turning in the opening.
AnimatedOpen frame band saw, 2.1 m (Woodworking Workshop and Joinery)
Green cast frame band saw: a heavy plinth, a full height column carrying two exposed 400 mm wheels with charcoal tyres, a tilting steel table with its fence, an adjustable blade guard on its post, a dust port at the lower wheel and a start and stop station.
Planer thicknesser, 1.65 m (Woodworking Workshop and Joinery)
Over and under planer thicknesser in red: infeed and outfeed cast tables set either side of the cutterblock with the infeed 2 mm low, a long steel fence at the back, a yellow bridge guard, a rise and fall handwheel with its scale, an extraction hood and a start and stop station.
AnimatedSliding mitre saw on a folding stand, 1.9 m (Woodworking Workshop and Joinery)
Red sliding mitre saw on a grey folding stand: splayed legs under two top rails, a roller support wing at each end, a charcoal base with a rotating mitre table and a fence, and a saw head on its rear pivot that tilts down through the cut and back.