Free models · Game-ready GLB
Exterior
Every stylized model below is a self-contained .glb under 25 MB that drops into three.js, Blender, Godot, Unity and Unreal, free to use and modify in commercial projects without attribution.
Load one straight from its CDN URL with a plain GLTFLoader, or take a whole themed set from the packs.
2,013 free GLB models
Stylized Pine Tree Wide (Stylized Trees and Rocks Kit)
Broad stylized pine with a sturdy trunk and three wide layered needle shelves forming a classic spreading crown.
Stylized Pine Tree Sapling (Stylized Trees and Rocks Kit)
Small stylized pine sapling with a short stem and two rounded needle tiers for fresh planting and undergrowth.
Stylized Pine Tree Tall (Stylized Trees and Rocks Kit)
Tall narrow stylized pine with a straight bole and four stacked needle cones for windbreaks and background stands.
Finish Line Plate (Velodrome and Track Cycling)
The finish line across the track: a 0.55 m overlay plate of ten black and white blocks running the full 6 m width, cut to the straights 13 degree camber so it lies flush on a straight module in front of the judges tower.
Pursuit Line Plate (Velodrome and Track Cycling)
The white pursuit line across the full 6 m width of the track, on a 0.5 m overlay plate cut to the same 13 degree camber. Two of these sit half a lap apart on opposite straights, which is where a pursuit starts and finishes.
Track Surface Board Panel (Velodrome and Track Cycling)
A spare panel of track decking, 2.4 by 1.2 m of pale pine boards on two steel bearers, for laying flat in the track centre as a repair stack or a working platform. Six raised boards read as the plank courses of the running surface.
Sprinters and Stayers Line Plate (Velodrome and Track Cycling)
An 8 m overlay plate carrying the three lines that run the length of the track: the white measurement line 0.2 m up from the inner edge, the red sprinters line at 1.05 m and the blue stayers line at 2.45 m. Cut to the straights 13 degree camber and laid on a straight module.
Track Apron Bend Module (Velodrome and Track Cycling)
The curved 30 degree length of the apron, cut to a 9.4 m inner radius so it closes round the ends of the track centre. The origin is the centre of the circle it is cut from.
Track Apron Module (Velodrome and Track Cycling)
An 8 m length of the flat concrete apron between the track centre and the cote d azur, 3 m wide and 0.35 m thick so its surface is level with the tracks inner edge. Ports at both ends.
Cote d'Azur Strip Module (Velodrome and Track Cycling)
The 0.6 m blue strip that runs round the inside of the racing surface, level with the apron and flush with the tracks inner edge. An 8 m straight length with ports at both ends.
Cote d'Azur Bend Module (Velodrome and Track Cycling)
The curved 30 degree length of the blue strip, cut to the same 13 m inner radius as the bend modules it sits against. The origin is the centre of the circle, so twelve of these close the two bends.
Banked Track Bend Module (Velodrome and Track Cycling)
A 30 degree segment of velodrome bend: 6 m of timber surface banked at a constant 42 degrees on a 13 m inner radius, carried on steel bents. The origin is the centre of the circle it is cut from, so four of these and two transitions turn a half lap.
Banked Track Transition Module (Velodrome and Track Cycling)
A 30 degree segment easing the bank from the straights 13 degrees to the bends 42 with a smoothstep, on the same 13 m inner radius and the same ports, so the track changes slope gradually instead of stepping between flat pieces set at angles.
Banked Track Transition Module (Mirrored) (Velodrome and Track Cycling)
The handed pair of the transition segment, easing from 42 degrees of bend back down to the 13 degree straight across its 30 degrees. A bend takes one of each, so the surface leaves and rejoins the straight at the same slope it arrives with.
Banked Track Straight Module (Velodrome and Track Cycling)
An 8 m straight of velodrome track, 6 m of timber surface banked at 13 degrees, standing on steel trestle bents with the inner edge on the floor. Ports at each end on the mid radius, so straights tile into the home and back straights of a lap.
Scale Reference Figure (Dragons and Wyverns)
Blank 1.75 m human figure in one flat material, for reading the size of every dragon in the pack.
AnimatedDisplay Plinth With A Turntable (Dragons and Wyverns)
Round timber plinth 0.86 m tall whose banded top turns on its own node. Stand an egg, a skull or a hatchling on it.
AnimatedIron Cage With An Opening Door (Dragons and Wyverns)
Barred iron cage 2.56 m square and 2.6 m high with a timber floor and a door on its own hinge node.
Chain And Shackle Anchor (Dragons and Wyverns)
Stone anchor block with a ring, a run of eight iron chain links across the ground and an open shackle.
Cliff Ledge (Dragons and Wyverns)
Rock shelf 5.6 m wide with its top at 2.5 m and two boulders on the back edge.
Cave Mouth Arch (Dragons and Wyverns)
Rock arch about 10 m wide and 6 m high over a dark opening. A backdrop, not an interior.
Lair Ground Tile (Dragons and Wyverns)
Six metre square of rocky lair floor, 140 mm thick and flat topped, with loose stones scattered on it.
Lair Perch Rock (Dragons and Wyverns)
Flat topped rock 4 m across with its top at 1.62 m, for perching a dragon or a wyvern on.
Claw Marks Ground Plate (Dragons and Wyverns)
Round earth plate 2.7 m across with four raked claw gouges across it, 40 mm proud.