Free models · CC0
Exterior
Every model below is a self-contained .glb under 5 MB, released under CC0 1.0 so it can be used and modified in commercial projects without attribution.
Load one straight from its CDN URL with a plain GLTFLoader, or take a whole themed set from the packs.
4,093 free GLB models
Bergschrund lip (Mountaineering and Summit Expedition)
Four-metre section where the glacier pulls away from the headwall, leaving an open gap under a two-metre ice lip.
Rock band step (Mountaineering and Summit Expedition)
Four-metre wide rock step with a 1.7 m rise, a broken ledge above, a snow gully at the foot and a fixed line.
Summit cairn (Mountaineering and Summit Expedition)
Stacked stone summit cairn about 1.2 m high with a wand and two strips of marker tape.
Moraine ground tile (Mountaineering and Summit Expedition)
Four-metre square moraine tile of loose rubble over glacier ice, the surface base camp is levelled on.
Serac block (Mountaineering and Summit Expedition)
Leaning three-metre tower of fractured glacier ice with a wind-loaded cap and collapsed blocks at the foot.
Stove and pot set (Mountaineering and Summit Expedition)
Gas cartridge stove with pot supports, a wide pot and lid, a wrapped windscreen and a spare cartridge.
Glacier goggles (Mountaineering and Summit Expedition)
Wide cylindrical-lens goggles in a foam-backed frame with an elasticated strap laid out behind.
High-altitude double boots (Mountaineering and Summit Expedition)
Pair of double boots with integral gaiters, front zips, lace hooks and welts for crampon bails.
Summit pack (Mountaineering and Summit Expedition)
Thirty litre lidless summit pack on the same back system, stripped for a summit day.
Climbing harness with rack (Mountaineering and Summit Expedition)
Padded sit harness on a stand, with four gear loops carrying karabiners, slings and a belay device.
Oxygen mask and regulator (Mountaineering and Summit Expedition)
Oro-nasal mask with an exhalation port and reservoir, on a corrugated hose to a regulator block.
Expedition pack (Mountaineering and Summit Expedition)
Seventy-five litre expedition pack with a lid, hip belt, compression straps, axe loops and a strapped rope.
Oxygen cylinder (Mountaineering and Summit Expedition)
Filament-wound oxygen cylinder with a neck valve, gauge, carry ring and a protective cage.
Climbing helmet (Mountaineering and Summit Expedition)
Hybrid shell climbing helmet with side vents, headlamp clips and an adjustable chin harness.
Twelve-point crampons, pair (Mountaineering and Summit Expedition)
Pair of step-in twelve-point crampons with front points, toe bail, heel lever and retaining straps.
Technical ice tools, pair (Mountaineering and Summit Expedition)
Matched pair of bent-shaft technical tools, one with a hammer and one with an adze, with grip rests.
Coiled climbing rope (Mountaineering and Summit Expedition)
Sixty-metre single rope flaked into a butterfly coil, waist-wrapped and tied off with two tails.
Mountaineering ice axe (Mountaineering and Summit Expedition)
Classic 66 cm walking axe with a curved toothed pick, adze, moulded grip, spike and a wrist leash.
Plastic rescue sled (Mountaineering and Summit Expedition)
Moulded rescue sled with runners, four casualty straps, a head-end bar and a tow bridle on a karabiner.
Route marker wand line (Mountaineering and Summit Expedition)
Six route wands set out over seven metres, each with a flag panel and packed snow at the foot.
Snow bollard (Mountaineering and Summit Expedition)
Horseshoe trench cut in hard snow leaving a load-bearing bollard, with the rope laid in the groove.
Haul bag (Mountaineering and Summit Expedition)
Reinforced cylindrical haul bag with a closure flap, four-point haul suspension and shoulder straps.
Ice screw cluster (Mountaineering and Summit Expedition)
Five tubular ice screws of graded length racked on a karabiner with a sling.
Fixed rope anchor on pickets (Mountaineering and Summit Expedition)
Three T-section snow pickets driven back and equalised to one master point carrying a fixed rope.