Free models · Game-ready GLB
Kit
Every modern model below is a self-contained .glb under 25 MB that drops into three.js, Blender, Godot, Unity and Unreal, free to use and modify in commercial projects without attribution.
Load one straight from its CDN URL with a plain GLTFLoader, or take a whole themed set from the packs.
4,897 free GLB models
Boat cradle (Marina and Yacht Club)
Adjustable steel boat cradle 4.6 m long: a welded base frame on pads with four padded side props on screw jacks, a keel bearer with timber blocks and a ladder hooked to one end, for standing a hull in the yard.
AnimatedTravel boat hoist with slings (Marina and Yacht Club)
Self propelled travel hoist 7.4 m wide and 6.2 m tall: a yellow portal frame on four steered wheel bogies, a driver's platform, two sling beams with webbing strops and a cross traverse. The slings lift and the beam traverses.
Dinghy rack (Marina and Yacht Club)
Galvanised three bay dinghy rack 6.4 m long and 2.4 m tall: two tiers of padded cradle arms on braced frames, with a ground rail, bay number plates left blank and a stowed pair of hulls resting on the lower tier.
AnimatedSailing dinghy on a launching trolley (Marina and Yacht Club)
Two person sailing dinghy 3.9 m long on a galvanised launching trolley: a glassfibre hull with side tanks, thwart, centreboard case and rudder stock, chocked on padded bunks with a handle and two pneumatic wheels that roll.
RIB tender, 4.2 m (Marina and Yacht Club)
Rigid inflatable tender 4.2 m long: a grey glassfibre vee hull with charcoal sponsons, a teak slatted sole, a centre console with a blank display and a grab rail, two jockey seats, an outboard on the transom and bow towing eye.
Motor cruiser with flybridge, 11.5 m, navy (Marina and Yacht Club)
Planing motor cruiser 11.5 m long: a hard chine hull with a bathing platform and shaft legs, a glazed saloon and helm, a teak cockpit, side decks with guardrails, and an open flybridge with its own console and rails.
Motor cruiser with flybridge, 11.5 m (Marina and Yacht Club)
Planing motor cruiser 11.5 m long: a hard chine hull with a bathing platform and shaft legs, a glazed saloon and helm, a teak cockpit, side decks with guardrails, and an open flybridge with its own console and rails.
Yacht mast with boom and standing rigging (Marina and Yacht Club)
Deck stepped aluminium mast 12.6 m tall with a swept spreader pair, cap and lower shrouds, a forestay and backstay, a kicking strap, a boom on its gooseneck, mast steps and a masthead fitting with a blank wind vane.
AnimatedSloop deck module with cockpit and wheel (Marina and Yacht Club)
Aft deck section of a cruising sloop 3.6 m long: a teak cockpit sole, coamings, helm seat, a wheel on its pedestal with a blank instrument pod, two primary winches, a locker top and a stern rail. The wheel and winches turn.
Sailing yacht hull, 9.6 m (Marina and Yacht Club)
Cruising sloop hull 9.6 m long with white topsides: a moulded deck, a coachroof with hatches and sliding companionway, a teak cockpit sole, guardrails, pulpit and pushpit, and a fin keel with a lead bulb below the waterline.
Furled sail set (Marina and Yacht Club)
Sail set stowed as a boat lies on its berth: a mainsail flaked on the boom under a navy sail cover with tie straps, and a headsail rolled on its foil with a UV strip, both in plain cloth with no sail number or insignia.
Sailing yacht hull, 9.6 m, navy (Marina and Yacht Club)
Cruising sloop hull 9.6 m long with navy topsides: a moulded deck, a coachroof with hatches and sliding companionway, a teak cockpit sole, guardrails, pulpit and pushpit, and a fin keel with a lead bulb below the waterline.
Mooring pile (Marina and Yacht Club)
Steel mooring pile standing in the basin: a 0.42 m tube driven from the bed to 3.1 m above the water with a charcoal cap, a yellow band and a welded ladder rung set, for holding a pontoon run or a berth in place.
Jetty lamp (Marina and Yacht Club)
Marina jetty lamp 2.6 m tall: a galvanised column on a charcoal base with a navy shroud, a downward lantern with a frosted lens and a low level marker light, for lighting a pontoon walkway or a quay edge.
Fender set on a rail (Marina and Yacht Club)
Set of three cylindrical boat fenders 0.6 m long hung on a short galvanised rail by their lanyards, with a flat pontoon fender board behind them, for a berth face or the side of a workboat.
Pile guide collar (Marina and Yacht Club)
Galvanised pile guide for a floating pontoon: a collar bracket with four rubber rollers running on a 0.42 m pile, a bolted deck arm and a safety chain eye, so a pontoon rises and falls without moving off station.
Wash down point with hose reel (Marina and Yacht Club)
Quayside wash down post 1.3 m tall: a galvanised post on a concrete plinth with a drum hose reel, a lance in its clip, a stop tap and a drain grating at its foot, for rinsing a boat down after a lift out.
AnimatedFuel berth pump (Marina and Yacht Club)
Marina fuel pump 1.9 m tall on a bunded plinth: a yellow cabinet with a blank display panel, a charcoal hose reel, a delivery nozzle in its holster and a spill kit locker, with hazard banding. The nozzle lifts out of the holster.
Berth service pedestal (Marina and Yacht Club)
Marina service pedestal 1.25 m tall: a galvanised column on a charcoal base with two shuttered power sockets, a metered water point with a tap and hose union, a blank berth plate and a navy lit head, for the deck edge of a pontoon.
Pump out station (Marina and Yacht Club)
Holding tank pump out unit on a pontoon: a grey cabinet with a vacuum pump housing, a coiled suction hose on a reel, a deck fitting wand in a bracket, a rinse tap and a blank instruction panel, on a bunded base.
AnimatedDock box (Marina and Yacht Club)
Berth holder's dock box 1.2 m by 0.6 m: a moulded white case on a charcoal plinth with a navy lid on piano hinges, a hasp, two side handles and a blank name plate. The lid lifts.
Pontoon boarding ladder (Marina and Yacht Club)
Man overboard ladder hung on a pontoon edge: a galvanised head frame bolted to the deck, two stiles dropping 1.2 m into the water, four treads and a charcoal grab loop, with a yellow head plate.
Pontoon mooring ring (Marina and Yacht Club)
Flush mooring ring for a pontoon or a quay coping: a 160 mm galvanised ring on a lugged back plate with four countersunk bolts and a short strop through it, sitting proud of the surface by 30 mm.
Pontoon cleat with warp (Marina and Yacht Club)
Galvanised 250 mm mooring cleat on a bolted base plate with a warp dressed over it in a loose figure of eight and run off toward the berth, for the deck edge of a pontoon or a finger.