Free models · Game-ready GLB
Props
Every modern prop below is a self-contained .glb under 25 MB that drops into three.js, Blender, Godot, Unity and Unreal, free to use and modify in commercial projects without attribution.
Load one straight from its CDN URL with a plain GLTFLoader, or take a whole props set from the packs.
7,008 free GLB models
AnimatedPinsetter Machine Housing (Bowling Alley and Pool Hall)
The pinsetter that stands behind a pin deck on the lane pitch: a welded frame with side sheets, the accent masking panel a bowler sees above the pins, the distributor drum and chutes inside, and a control box. The cowl over the machine deck lifts on its back edge.
Bowling Pin (Bowling Alley and Pool Hall)
A single ten pin on the real profile: 381 mm tall, 121 mm across the belly, in coated white with the two red neck stripes and the dark base ring that keep it readable against a pale floor.
Guitar Wall Hanger (Music Recording Studio and Instruments)
A timber backed guitar wall hanger: a screwed plate with a steel stem and two sleeved yoke arms 140 mm apart, which is the cradle a guitar neck hangs in. The plate sits flat against the wall.
Studio Wall Clock (Music Recording Studio and Instruments)
A 260 mm studio wall clock: a matt black case with a cream dial, twelve markers, hour and minute hands and a red sweep hand. The back of the case sits at z=0 so it hangs flat on a wall.
Coffee Mug (Music Recording Studio and Instruments)
A 350 ml stoneware mug 100 mm tall with a banded glaze, a loop handle and coffee in it, for the console armrest.
Water Bottle (Music Recording Studio and Instruments)
A 750 ml water bottle 280 mm tall with a moulded waist, a printed band and a screw cap, for the corner of a desk or the top of an amp.
Studio Rug (Music Recording Studio and Instruments)
A 2.6 by 1.9 m patterned rug in teal, red and amber with a fringed edge, 10 mm thick. A kit is set up on one because it stops the drums walking and takes the ring off the floor.
Drum Throne (Music Recording Studio and Instruments)
The same stool built as a drum throne: a wider, deeper padded seat at 550 mm on a three leg frame, which is the height and the spread a kit is played from.
Studio Stool (Music Recording Studio and Instruments)
A 660 mm padded studio stool: a round upholstered seat on a four leg steel frame with a foot ring and rubber tips, for a guitarist, an engineer or a spare seat at the desk.
Music Stand (Music Recording Studio and Instruments)
A folding music stand at 1.06 m with a sheet on its desk: a perforated steel desk on a raked hinge, a telescopic column and a rubber footed tripod.
AnimatedFlight Case, Small (Music Recording Studio and Instruments)
The same ply flight case in a 560 by 400 by 400 mm size without castors, for microphones, leads and small outboard.
AnimatedFlight Case, Large (Music Recording Studio and Instruments)
A 920 by 560 by 580 mm ply flight case on castors: a riveted shell with aluminium extrusion edging, eight corner caps, two butterfly latches, spring handles, an amber lid label and a lid hinged along its back edge.
AnimatedCable Drum (Music Recording Studio and Instruments)
A 540 mm timber cable drum wound with black multicore, resting on its flanges with the tail led off and coiled on the floor beside it.
Isolation Screen (Music Recording Studio and Instruments)
A free-standing 900 by 1800 mm isolation screen: a framed 70 mm absorber in grey fabric on a steel post frame with weighted feet. Its screen-left and screen-right ports meet the next screen square or at a right angle, so three of them fold into a vocal booth.
AnimatedTwo Inch Tape Machine (Music Recording Studio and Instruments)
A two inch multitrack tape machine, the hero piece of a control room: a pedestal cabinet with a timber front under an upright transport deck carrying two 10 inch reels with spoked flanges and brass hubs, a head block, five transport buttons and two meters. 1.3 m tall.
Patch Bay Panel (Music Recording Studio and Instruments)
A 2U 19 inch patch bay: 48 quarter inch jacks in two rows of 24 with designation strips between them, on a rack panel with mounting ears. It stands on its bottom edge so it can be dropped straight into a rack.
Monitor Controller (Music Recording Studio and Instruments)
A desktop monitor controller, 200 by 170 mm: a weighted wedge with a large volume encoder in a ring, four source and mute buttons and a small meter display.
Headphones on a Wall Hook (Music Recording Studio and Instruments)
A pair of closed back studio headphones hanging on a wall hook: a padded headband, two swivel cups with fabric pads and an alloy yoke, on a screwed wall plate. The plate sits flat against the wall with the hook 75 mm proud of it.
AnimatedStudio Desk Chair (Music Recording Studio and Instruments)
An upholstered studio chair on a five star castored base: a padded seat and back with a gas lift column and a pair of tube armrests, 1.0 m to the top of the back.
AnimatedOutboard Rack on Castors (Music Recording Studio and Instruments)
A 900 mm open frame outboard rack on four swivel castors, with a timber top, three pieces of 19 inch gear and a drawer in the bottom bay. It rolls between the control room and the live room.
AnimatedStudio Rack Cabinet (Music Recording Studio and Instruments)
A 1.15 m timber sided rack cabinet on rubber feet, loaded with 19 inch outboard: a compressor, a channel strip, a converter, a power conditioner and a patch strip, with meter windows, knob rows and rack screws, plus a shallow accessory drawer on slides.
Studio Desk with Screen Pair (Music Recording Studio and Instruments)
A 1.6 m studio desk in dark timber with a steel underframe, a lower shelf and a modesty panel, carrying a pair of 24 inch screens on their feet, a keyboard and a mouse. The screens are turned in toward the engineer.
Mixing Console (Music Recording Studio and Instruments)
A 1.98 m analogue mixing console on timber side cheeks: sixteen channel strips of four knobs, a switch and a 100 mm fader on a raked bay, a master section, a meter bridge with two meter windows, and an armrest along the engineer side. It stands 1.02 m to the top of the bridge.
Studio Monitor on a Stand (Music Recording Studio and Instruments)
A two way nearfield studio monitor on a 940 mm pole stand: a 240 by 370 mm cabinet with a six inch woofer, a waveguide tweeter, a rear facing port tube and a status lamp, tipped back on a cast plate base.