3D Assets
@3dassets
Pad Water Tower (Rocket Launch Pad and Gantry)
A 22 m water tower feeding the deluge system: a lattice frame on four pads carrying an 8.4 m tank with a domed base and top, a railed catwalk, a ladder the full height and a downpipe out to the mains.
Safety Shower and Eyewash (Rocket Launch Pad and Gantry)
An emergency safety shower and eyewash station on a concrete plinth: a 2.6 m yellow standpipe with an overhead rose and pull rod, a bowl and paddle on the stem and a blank instruction plate on the back.
Cable Tray Run (Rocket Launch Pad and Gantry)
An 8 m elevated cable tray on two stanchions, 1.5 m to the deck, carrying three bundles in a ladder tray with side rails. Ported at both ends at tray height so a tray route crosses a pad without blocking it.
Blast Fence Panel (Rocket Launch Pad and Gantry)
A 4.4 m blast fence panel, 3.7 m tall: a braced steel frame on two ballast pads carrying a deflection plate with vertical stiffeners and a yellow cap rail. Ported left and right so a blast wall runs as far as the pad needs.
Sound Suppression Pipe Run (Rocket Launch Pad and Gantry)
An 8 m length of 1.1 m sound suppression water main on concrete saddles, with seven standpipes and outlet heads along the top and a control box on the flank. Ported at both ends, so a suppression ring is built from repeats.
Cable Trench Section (Rocket Launch Pad and Gantry)
An 8 m cast cable trench with five removable lid slabs, a cable bed inside and a yellow duct run along one wall. Ported at both ends so power and signal routes run from the firing room to the pad.
Deluge Pipe Run (Rocket Launch Pad and Gantry)
An 8 m run of 600 mm deluge main on concrete saddles, with flanged ends, a standpipe tapping and an isolation valve body. Ported at both ends on the pipe centreline so a water main runs the length of the pad.
Deluge Pipe Elbow (Rocket Launch Pad and Gantry)
The deluge main turning a right angle on the same 8 m module: a north port and a west port meeting at a swept bend on its saddles, so the water main can follow the pad boundary.
Water Deluge Head (Rocket Launch Pad and Gantry)
A 6.7 m deluge head: a mast on a concrete footing carrying a spray ring of eight nozzle arms, with the feed pipe coming in at ground level through a valve block and a ladder up the mast. Sprays are not modelled.
AnimatedLaunch Mount with Clamps (Rocket Launch Pad and Gantry)
The launch mount: a ring deck 11.5 m across on six columns over the trench mouth, railed all round, with a yellow kick ring for the vehicle skirt and four hold down clamps on hinge posts that swing clear at release. Umbilical plate and cryogenic risers on one flank.
Flame Deflector (Rocket Launch Pad and Gantry)
A steel framed double wedge deflector, 3.4 m wide and 2.8 m tall, that splits the exhaust plume down both arms of the trench. Ablative dark face, a bolted cradle underneath and a cooling water manifold along each flank.
Launch Table (Rocket Launch Pad and Gantry)
A 7.2 m steel launch table for a small vehicle: four jack posts on pads, a bolted deck frame with an open flame hole, a railed working deck, an access stair and a blank hazard plate on the front girder.
Flame Trench Section (Rocket Launch Pad and Gantry)
An 8 m section of flame trench: two 2.6 m concrete walls with a coping lip and a scorched lining, a sloped channel floor 3.4 m across, a drain sump and deluge nozzles along both kerbs. Ported at both ends so the trench runs as far as the pad needs.
Hardstand Module (Rocket Launch Pad and Gantry)
An 8 m hardstand module for parking transporters, carts and skids beside the pad: a gravel bed, a laid concrete deck with joint lines and a yellow kerb down each side. Ported on all four edges to the same grid as the apron.
Pad Apron Module (Rocket Launch Pad and Gantry)
An 8 m square reinforced concrete pad apron module, 180 mm thick, with cast joint strips, a central drain channel and four bolt groups. Edge ported north, south, east and west so an apron of any size tiles out of repeats.
Scorched Apron Module (Rocket Launch Pad and Gantry)
The pad apron module in flame washed dark concrete, with soot patches where the exhaust plume has swept the slab. Same 8 m module and the same four edge ports, so it drops straight into an apron built from the clean tiles.
Mosque Court and Madrasa Forecourt (Desert Mosque and Madrasa Courtyard)
A desert mosque and its teaching college round a 12 m court open to the sky: twelve pointed arch arcade bays and four corners closing three sides of it, the ablution fountain in the middle with runnels, trees, benches, lamps and a cistern round it, and an open sided hypostyle...
Minbar With Canopy (Desert Mosque and Madrasa Courtyard)
Free 3D model of a cedar minbar for a desert mosque: seven steps between pierced cheeks, an arched doorway at the foot and a seat under a muqarnas canopy, 3.5 m tall.
Standing Lamp (Desert Mosque and Madrasa Courtyard)
Free 3D model of a tall brass standing lamp for a desert mosque hall or courtyard: a turned column on a stone foot carrying a glazed lantern, 1.96 m tall.
Candle Stand (Desert Mosque and Madrasa Courtyard)
Free 3D model of a turned brass candle stand for a desert mosque or madrasa: a moulded column on a spread foot carrying a single wax candle, 1.21 m tall.
AnimatedHanging Lamp Small (Desert Mosque and Madrasa Courtyard)
Free 3D model of a 0.5 m pierced brass hanging lamp on a chain for a desert mosque or madrasa arcade, with glazed panels round the bowl.
AnimatedHanging Lamp Large (Desert Mosque and Madrasa Courtyard)
Free 3D model of a 0.8 m pierced brass hanging lamp on a chain for a desert mosque or madrasa arcade, with glazed panels round the bowl.
Laid Mat Run (Desert Mosque and Madrasa Courtyard)
Free 3D model of a 3 m laid reed mat run for a desert mosque prayer hall: woven reeds with binding cords and a bound edge, 0.06 m deep.
Matting Roll (Desert Mosque and Madrasa Courtyard)
Free 3D model of a rolled reed matting bundle for a desert mosque or madrasa: a 1.8 m roll tied with two bands, with the end of the mat lying out of it.