Free models · Game-ready GLB
Interior
Every modern model below is a self-contained .glb under 25 MB that drops into three.js, Blender, Godot, Unity and Unreal, free to use and modify in commercial projects without attribution.
Load one straight from its CDN URL with a plain GLTFLoader, or take a whole themed set from the packs.
5,621 free GLB models
Respawn Pad Marking Tile (Laser Tag Arena and Activity Centre)
A 1 m square respawn pad: a thin dark plate laid over the arena floor with a cyan ring and four chevrons pointing into the middle of it, so a tagged player knows where to stand out the count.
AnimatedTarget Pod on Stand (Laser Tag Arena and Activity Centre)
A free standing target pod: a three legged foot, a 1 m column and a six faced magenta head banded in lime with a domed sensor on every face, so a pod is shootable from any approach.
Raised Platform Deck with Rail (Laser Tag Arena and Activity Centre)
A 2 by 2 m raised platform at 900 mm: a pale deck on a boxed dark frame with a brushed rail round three sides, a cyan kick band under the deck edge and the fourth side left open for the ramp. Ported on all four deck edges.
Arena Tunnel Section (Laser Tag Arena and Activity Centre)
A 2 m tunnel section 1.5 m wide and 1.7 m tall: a flat sided arch in dark composite with brushed end ribs and floor rails, and a lime stripe along the inside so a player can find the exit in the dark. Ported at both open ends so sections chain into a crawl.
Arena Ramp to Platform (Laser Tag Arena and Activity Centre)
A 2.4 m ramp up to platform height: a pale checker deck on a boxed dark frame with seven amber grip strips across it and an amber kerb each side, rising 900 mm at a walkable pitch. The high end carries a platform port so it lands square on a deck edge.
Low Arena Barricade (Laser Tag Arena and Activity Centre)
A 2 m barricade 1.1 m high: a raked dark face on a wide foot with a brushed capping rail and end posts, and five amber hazard flashes across it. Ported on the same run as the wall modules, so it drops into a wall line or stands as free cover.
Arena Corner Post Module (Laser Tag Arena and Activity Centre)
The 300 mm square corner post an arena wall run turns a right angle through: a dark column 2.4 m tall on a spreader plate, capped at the head, with a cyan stripe up all four faces. Ports on two adjacent faces at base rail height.
AnimatedArena Doorway Module (Laser Tag Arena and Activity Centre)
A 2 by 2.4 m arena wall module with a 1 m doorway through it: a dark leaf in a brushed steel lining with a lime vision slot and a full height push bar, on an amber threshold, ported like every other module so a door drops into any run.
Arena Mirror Panel Module (Laser Tag Arena and Activity Centre)
The arena wall module faced with a full height polished panel in a cyan bead frame: the piece that makes a maze corner unreadable, because a player sees a reflection where a route should be.
Arena Wall Panel Module (Laser Tag Arena and Activity Centre)
A 2 by 2.4 m arena wall module: a dark composite panel between two brushed stiles on a steel base rail with levelling feet, capped at the head, and carrying three raked magenta chevrons on the play side. Ported at both ends so a maze is built by repeating one model.
Arena Wall Panel with Shooting Port (Laser Tag Arena and Activity Centre)
The arena wall module with a 600 by 400 mm shooting port cut through it at chest height, lined in brushed steel and edged top and bottom in amber, so a maze has somewhere to shoot from as well as somewhere to hide behind.
Arena Floor Tile, Teal (Laser Tag Arena and Activity Centre)
The arena floor tile with teal marking instead of lime, for the opposing half of an arena or for the front of house floor, so a large floor does not read as one repeated model.
Arena Floor Tile (Laser Tag Arena and Activity Centre)
A 2 m square arena floor tile 60 mm deep: a grey resin screed in a shallow tray, marked with a lime border line, a centre bar and a chevron in each corner, ported on all four edges so a whole arena floor is laid from repeats of one model.
AnimatedPedal waste bin (Butcher's Shop and Deli Counter)
A 720 mm stainless pedal bin with a burgundy band, an inner liner rim, a modelled pedal and rod linkage, and a domed lid rigged to lift.
AnimatedStock trolley (Butcher's Shop and Deli Counter)
A three shelf stainless trolley with a push handle and a blank burgundy ticket holder, loaded with crated and boxed stock on the lower decks. All four castors are rigged to roll.
Floor drain grate (Butcher's Shop and Deli Counter)
A stainless slot grate in a coved kerb surround, sitting flush in a prep room floor over a dark trap. Nine bars on a framed border, at 30 mm above the floor tile.
AnimatedCleaning station with hose reel (Butcher's Shop and Deli Counter)
The wash down corner: a stainless panel on a kerb with a burgundy hose reel rigged to spin, the lead running down to a wash down gun, a tap set with lever handles, a brush and a squeegee on clips and two blank chemical jugs.
Packaging box shelf (Butcher's Shop and Deli Counter)
The packaging store: a two tier stainless shelf with burgundy edge rails, flat packed boxes below, film and foil rolls on the middle deck and a stack of trays under the top shelf.
Chiller hanging rail (Butcher's Shop and Deli Counter)
The braced rail a chiller hangs its work from: a stainless tee rail on two posts with seven roller hooks, standing over a pallet of boxed and trayed cuts. The hooks are modelled empty on purpose.
Stock crate stack (Butcher's Shop and Deli Counter)
Four stacking crates nested on a low dolly in alternating burgundy and white, each with a contrasting rim and hand grips on both ends.
Chiller shelving unit (Butcher's Shop and Deli Counter)
A 1.2 m four tier shelving bay on round stainless posts with adjustable feet, the decks edged alternately in burgundy and steel and loaded with boxed and crated stock.
Apron and hat hook rail (Butcher's Shop and Deli Counter)
A stainless wall rail on two brackets with five brass hooks, hung with a burgundy apron, a white apron and a folded hat with a burgundy band.
AnimatedWalk in chiller door module (Butcher's Shop and Deli Counter)
A 1.5 m wall module carrying the walk in chiller door: an insulated leaf 90 mm thick in a proud stainless frame, with a round viewing port, a burgundy kick plate, heavy hinges, a brass lever latch and a threshold ramp.
Hand wash basin (Butcher's Shop and Deli Counter)
The wall hung hand wash station a food room needs beside its door: a small stainless bowl on a bracket with a splashback, a lever tap and a blank soap dispenser in the house colour.