Free models · Game-ready GLB
Modern
Every modern model below is a self-contained .glb under 25 MB that drops into three.js, Blender, Godot, Unity and Unreal, free to use and modify in commercial projects without attribution.
Load one straight from its CDN URL with a plain GLTFLoader, or take a whole themed set from the packs.
14,038 free GLB models
Cellar deck section, 6 m (Offshore Oil Rig and Platform)
A 6 m bay of cellar deck: 1.2 m plate girders with diagonal bracing carrying grating around an open wellbay slot, a painted slot surround and a handrail run along one edge. Its top ports sit at main deck level, so a run of these drops straight into a deck grid as the wellbay.
Jacket boat landing and ladder (Offshore Oil Rig and Platform)
The boat landing hung on a jacket leg: two fendered stringers with five rubber fender tubes, a caged ladder up the face, a grated half landing with handrails at the top and a painted approach marker.
Deck module, chequer plate 6 m (Offshore Oil Rig and Platform)
The same 6 m deck module with a sealed chequer plate surface instead of open grating, for a laydown area, a module footprint or anywhere a dropped object must not fall through.
Deck module, open grating 6 m (Offshore Oil Rig and Platform)
A 6 m square of main deck: three primary beams and two edge girders under an open grating walking surface with its bearing bars standing proud. Tile the modules on the 6 m grid and a deck of any size falls out.
Jacket pile stub and mud mat (Offshore Oil Rig and Platform)
The mudline foundation a leg lands on: a heavy grouted pile can on a square mud mat, with four gusset stiffeners, a flanged head and a grout return line. Put it under the bottom leg section when the seabed is modelled.
Jacket bracing panel, 18 m (Offshore Oil Rig and Platform)
The 18 m X brace that ties two jacket legs into a frame: two tubular diagonals crossing a horizontal member, gusseted connection plates at both ends and a painted collar at the crossing node.
Jacket leg section, 6 m (Offshore Oil Rig and Platform)
A 6 m flanged tubular leg of a fixed steel jacket, with the darkened splash zone band, four sacrificial anodes and a hazard ring at each brace level. Stack the sections to reach any water depth and tie them with bracing panels.
Cutaway Plant Floor (Nuclear Power Station and Control Room)
A 48 by 32 m station floor built from the pack's own 4 m slabs and shown as a cutaway: there is no roof over the halls and no wall across the front, so the reactor hall, the control room and the turbine hall are all looked straight down into and walked through. At the back...
AnimatedFire and Emergency Station (Nuclear Power Station and Control Room)
A 1.1 m fire point: a red back panel on two feet with a spoked hose reel on a bolted bracket that turns on its own node, a nozzle clipped beside it, two extinguishers on brackets and a break glass call point.
Battery Room Rack (Nuclear Power Station and Control Room)
A 2.4 m two tier battery stand: sixteen cells in translucent cases on painted steel tiers, with terminal posts and copper link bars across every pair, and a blank tag strip at the head.
AnimatedVentilation Fan Unit (Nuclear Power Station and Control Room)
A plant ventilation fan on a concrete plinth: a 1.4 m casing with flanged duct connections, a discharge spigot on top, an eight bladed impeller behind a bar guard, the motor on the back and a local isolator with lamps.
Diesel Backup Generator (Nuclear Power Station and Control Room)
A 4.4 m standby diesel generator on a skid: an eight cylinder engine with rocker covers, manifold and turbocharger, a guarded coupling to the alternator, a radiator and fan cowl at the far end, an exhaust stack and a local panel with gauges and lamps.
AnimatedSwitchgear Cubicle (Nuclear Power Station and Control Room)
A 900 mm switchgear cubicle 2.3 m tall: a recessed instrument compartment with a meter, lamp tiles and control switches, a breaker door with a racking aperture and a trip lamp, a cable box behind and an earth bar along the base.
Cable Tray Run (Nuclear Power Station and Control Room)
A 4 m bay of ladder cable tray on two stanchions at 2.8 m: pressed side rails with rungs on 300 mm centres and three cable bundles lying in it. End ports run it across a plant floor.
Cable Tray Corner (Nuclear Power Station and Control Room)
The cable tray turned through a right angle on two stanchions, for taking a run round a corner of the plant floor.
Bus Duct Riser (Nuclear Power Station and Control Room)
The bus duct bay with a riser dropping off one end to a cubicle top, with its link box and floor flange, for taking a run down to switchgear.
Bus Duct Run (Nuclear Power Station and Control Room)
A 4 m bay of enclosed bus duct on its own stanchions at 3 m: a galvanised casing with bolted joint covers, an inspection panel, phase marking beads and a blank tag. End ports run it across a plant floor.
AnimatedSwitchyard Transformer (Nuclear Power Station and Control Room)
A 3 m oil filled transformer on its bund plinth: a welded tank with radiator banks down both flanks, three bushings on the lid and three on the end, a conservator drum over them, a marshalling box with gauges and lamps, and a tap changer handwheel that turns.
Radiation Warning Sign Post (Nuclear Power Station and Control Room)
A 1.8 m boundary sign post on a footplate: a yellow board with the trefoil and a blank plate under it, and a chain eye on each side of the post for closing off an area.
AnimatedWaste Drum, Unmarked (Nuclear Power Station and Control Room)
The waste drum in plain galvanised finish for clean side use, with the same hinged lid.
AnimatedDrum Stacker (Nuclear Power Station and Control Room)
A hand hydraulic drum stacker: straddle legs on castors, a 2.1 m mast with a head sheave, a pump body with its lever at the back, and a carriage with a drum clamp ring that lifts on its own node.
Waste Drum, Lid Open (Nuclear Power Station and Control Room)
The waste drum with its lid held open at 96 degrees and the bag ring inside on show, for a drum being filled. The open pose is baked into the geometry, so the lid does not animate.
AnimatedWaste Drum (Nuclear Power Station and Control Room)
A 200 litre waste drum: a rolled steel body with two swage ribs, a trefoil on the flank and a clamp banded lid hinged at the back that lifts on its own node.
AnimatedSample Glovebox (Nuclear Power Station and Control Room)
A 1.5 m stainless sampling glovebox on a tubular stand: a sloped laminated window, two glove ports with the gloves hanging inside, a transfer port on the end, an extract duct off the top and a tool drawer in the stand.