3D Assets
@3dassets
Plastic Crate Stack, Blue (Allotments and Community Garden)
The same stack of three crates in pale blue, for mixing colours across a plot. The geometry is unchanged.
Upturned Pot Stack (Allotments and Community Garden)
Four terracotta pots stacked upside down to keep the rain out, 0.63 m high, with two more stood beside them in the grass. One static solid; the pots do not separate.
Plastic Crate Stack (Allotments and Community Garden)
Three stacked ventilated produce crates, just over a metre to the top of the pile and set down slightly out of square. The crates are one solid: they do not come apart or nest.
AnimatedBird Scarer on a Pole (Allotments and Community Garden)
A 1.9 m pole with four arms of old discs and cut plastic streamers on the head, turned by the wind over a sown bed. The head is one node on the pole, so the clip spins the whole spider; the streamers do not flutter on their own.
AnimatedCommunal Tool Store (Allotments and Community Garden)
The site's shared store: a 3 x 2 m timber building 2.3 m at the front under a corrugated pent roof, with a wide braced door and a padlock. The door is one node on its hinge stile; the roof sheets and the padlock are fixed.
Honesty Box Stall (Allotments and Community Garden)
A 1.3 m trestle stall of surplus produce by the gate, with two crates of greens, a painted price card and a locked honesty box with a coin slot. The box is a solid model: it does not open and holds nothing.
National Beehive (Allotments and Community Garden)
A 1.4 m national beehive on a timber stand: a floor, three brood and super boxes with handholds, a crown board and a galvanised roof, with the entrance block at the front. The boxes are modelled as one static stack; nothing lifts off and there are no bees.
Picnic Table (Allotments and Community Garden)
A 1.8 m timber picnic table with benches on both sides, 0.74 m to the table top on crossed A-frame legs. One static solid; the benches are part of the frame.
Hand Painted Site Noticeboard (Allotments and Community Garden)
A 1.8 m hand painted allotment noticeboard on two posts under a little pitched hood, with the site name lettered across the head and four notices pinned to it. The notices are painted geometry and cannot be changed at runtime.
Orchard Apple Tree (Allotments and Community Garden)
A 3.4 m allotment apple tree on a 1.5 m trunk with three low limbs, a broad crown and fruit on it, standing in rough grass. The crown is solid foliage: there is no leaf card, wind or sway.
Hedgerow Section (Allotments and Community Garden)
A 2 m run of mixed boundary hedge 1.5 m high on woody stems, with rough grass at the foot and berries in it. Run ports on both ends, so sections make a boundary of any length.
Timber Fence Panel (Allotments and Community Garden)
A 2 m closeboard fence bay 1.15 m high: two posts, a gravel board, two arris rails and eleven feather edge boards. Run ports on both ends, so bays make a boundary of any length.
Chain Link Fence Panel (Allotments and Community Garden)
A 2 m galvanised chain link bay 1.15 m high on two posts with top and bottom straining wires and a raking stay. The mesh is rigid geometry and does not sag. Run ports on both ends.
AnimatedSite Gate with Padlock (Allotments and Community Garden)
A 2 m allotment site gate: a four rail braced timber leaf hung between two 1.46 m capped posts, with a hasp and a padlock on the closing stile. The leaf is one node on its hinge post, so the clip swings it; the padlock is modelled shut and does not open.
AnimatedChicken Coop with Run (Allotments and Community Garden)
A raised timber coop 1.16 m across on 0.42 m legs with a felt gable roof, a pop hole and ramp, and a 1.7 x 1.1 m netted run on the end. The nest box hatch is one node hinged on its head; the netting, ramp and pop hole are fixed.
Bonfire Ring (Allotments and Community Garden)
A 1.4 m ring of reclaimed bricks round a bed of ash, with half burnt prunings stacked in the middle and a pile of green waste beside it. Nothing burns: there is no fire, smoke or light in the model.
AnimatedHose Reel on a Post (Allotments and Community Garden)
A hose reel on a galvanised bracket bolted to a 0.94 m post, wound with 0.22 m coils and a crank on the side, with the free end run off across the ground. The reel is one node on its axle so the clip spins it; the hose itself is a rigid solid and does not pay out.
Watering Can, Five Litre (Allotments and Community Garden)
The same can at two thirds the size, for seedlings and for a child to carry. The rose, spout and both handles are modelled; nothing moves.
Watering Can, Ten Litre (Allotments and Community Garden)
A galvanised ten litre watering can, 0.42 m to the handle, with a real rose on the end of the spout and a grip at the back. The rose is fixed to the spout and does not come off.
Hoe and Rake (Allotments and Community Garden)
A draw hoe and a seven tine soil rake stood head down in the earth with their 1.5 m ash handles crossing. The heads carry real blades and tines; the pair is one static model.
AnimatedWheelbarrow (Allotments and Community Garden)
A galvanised builders barrow with timber handles, a stub axle and two leg stands, 1.5 m over the handles. The wheel is one node on the axle, so the clip rolls it; the barrow itself does not tip.
Garden Fork and Spade in the Earth (Allotments and Community Garden)
A digging spade and a four tine fork left standing in a heap of turned earth, both 1.15 m to the top of the D handle, with a real blade, tread and shoulder. Static: the tools and the heap are one model.
Tool Rack (Allotments and Community Garden)
A 1.14 m boarded tool rack that leans against a shed wall, with four hooks, a hand fork, a trowel, a ball of twine and a seed box on it. The hung tools are part of the rack and do not come off.
Standpipe and Tap on a Post (Allotments and Community Garden)
The site standpipe: a galvanised riser strapped to a timber post on a concrete pad, 1.2 m to a brass tap with a drip tray and a bucket under it. Nothing turns; the tap head is modelled in one piece.