Free models · Game-ready GLB
Interior
Every modern model below is a self-contained .glb under 25 MB that drops into three.js, Blender, Godot, Unity and Unreal, free to use and modify in commercial projects without attribution.
Load one straight from its CDN URL with a plain GLTFLoader, or take a whole themed set from the packs.
5,345 free GLB models
Belt drive air compressor, 200 litre (Car Repair Garage and MOT Workshop)
Horizontal receiver compressor: a blue tank on saddle feet with a drain cock, a two cylinder pump with finned heads and a spoked flywheel under a charcoal belt guard, the motor behind it, a pressure switch, two gauges and the outlet line.
Pair of ratchet axle stands (Car Repair Garage and MOT Workshop)
Two 3 tonne axle stands side by side: folded sheet tripod legs, a ratchet post with visible teeth, a cast saddle with a vee notch and a pivoting pawl with its handle, both set at working height.
AnimatedLow profile trolley jack, 3 tonne (Car Repair Garage and MOT Workshop)
Long chassis trolley jack in workshop red: two side plates, front rollers and rear swivel castors, a lifting arm with a saddle pad, the pump body and a two piece handle in its socket that rocks as it is pumped.
Telescopic transmission jack (Car Repair Garage and MOT Workshop)
Under-lift gearbox jack: a wide charcoal base on four castors, a two stage telescopic ram, a pump pedal and a tilting saddle with corner posts and two ratchet strap hooks.
Rotating engine stand (Car Repair Garage and MOT Workshop)
Blue engine stand: a four leg base on castors, an upright with a locking collar, a splined rotating shaft and a four arm mounting head with slotted arms and bolt pads for hanging a block.
AnimatedFolding engine hoist, 2 tonne (Car Repair Garage and MOT Workshop)
Red folding engine crane: a wide A frame on four castors, an upright mast with a gusset, a stepped boom with four pin holes, a hydraulic ram under it, and a chain with a grab hook on the nose. The boom tilts and the castors roll.
AnimatedRolling tool chest with seven drawers (Car Repair Garage and MOT Workshop)
Red roller cabinet 1.06 m wide on four braked castors: seven drawer fronts with full width pulls on runners, a charcoal work top with a raised lip, a side handle and a blank badge plate, each drawer opening on its own.
Two shelf tool trolley (Car Repair Garage and MOT Workshop)
Open steel service trolley on four castors: two dished shelves with raised lips, a push handle, a socket rail with six sockets standing in it and a hanging rail of open ended spanners down one side.
Headlight aim tester on a floor rail (Car Repair Garage and MOT Workshop)
Beam setter on a 3 m floor rail: a charcoal mast on a rolling carriage, a grey optical box with a fresnel lens and a mirror sight, a spirit level bar across the top and a graduated scale up the mast.
AnimatedExhaust extraction hose reel (Car Repair Garage and MOT Workshop)
Ceiling mounted fume extraction reel: a bracket and a fan housing with a grey drum wound with charcoal ducting, a drop length of ribbed hose and a steel tailpipe nozzle with its clamp handle.
AnimatedBrake roller tester plate set (Car Repair Garage and MOT Workshop)
Pair of sunken roller beds for a brake test lane: knurled steel rollers on each side of a bright feeler roller, charcoal frames with yellow edge markings, set 1.7 m apart on the track of a car.
Four post vehicle lift with drive-on ramps (Car Repair Garage and MOT Workshop)
Four post drive-on lift with its runways at 1.1 m: blue columns on base plates, checker plate runways with wheel stops and a jacking beam between them, hinged ramps off the back end and a floor level power pack with its control box.
AnimatedTwo post vehicle lift, 2.9 m (Car Repair Garage and MOT Workshop)
Clear floor two post lift: yellow columns on bolted base plates, a top beam with the cable duct, a control box with a green start and a red stop, and steel carriages carrying four telescoping swing arms with rubber lifting pads, shown at the floor and rising on a vertical travel.
Inspection pit bay section, 4 m (Car Repair Garage and MOT Workshop)
Four metre bay section with an inspection pit through it: concrete either side of a 0.96 m shaft, a yellow painted edge stripe, a galvanised lip angle, two recessed pit lights and the open shaft below, joining end to end with the next section.
Two post vehicle lift, raised (Car Repair Garage and MOT Workshop)
The same two post lift with its carriages and swing arms baked at full 1.8 m working height, for a bay that should read as occupied without running a clip. The arms are set to the same spread as the lowered model.
Workshop floor tile, plain, 4 m (Car Repair Garage and MOT Workshop)
The same 4 m concrete floor module without the painted bay outline, for walkways, the tyre bay and the reception corner. Identical edge ports, so it lays into the same grid.
Workshop floor tile with bay markings, 4 m (Car Repair Garage and MOT Workshop)
Power floated concrete floor module 4 m square and 120 mm thick, with a painted safety yellow bay outline standing 5 mm proud of the slab and edge ports on all four sides.
Workshop wall panel module, 4 m (Car Repair Garage and MOT Workshop)
Ribbed steel cladding panel 4 m wide and 2.8 m tall on a concrete plinth, with a capping rail, side ports on the centre line and a top port for the glazed strip that courses above it.
Workshop window strip module, 4 m (Car Repair Garage and MOT Workshop)
Glazed clerestory course 4 m wide and 1.2 m tall with charcoal mullions, sill and head, built to sit on the wall panel's top port and carry the run up to 4 m.
Wet floor sign (Petrol Station and Forecourt Shop)
A folding hazard A frame in amber with two blank pictogram panels and a hinge strap, for the shop floor after a delivery or a spill.
AnimatedDelivery roll cage (Petrol Station and Forecourt Shop)
The wheeled cage a shop delivery arrives in: a steel frame with wire mesh on three and a half sides, a loaded deck, a top frame, a blank hazard label and four castors rigged to roll.
AnimatedStock trolley (Petrol Station and Forecourt Shop)
A three shelf picking trolley loaded with shop stock, with a push handle, a blank ticket holder and four castors. All four wheels are rigged to roll.
Oil and additive shelf unit (Petrol Station and Forecourt Shop)
A narrow four shelf unit of oil and additive bottles, each with a real neck and cap, with accent price rails and a blank header. Stands against a wall inside or by the forecourt door.
AnimatedShop cash machine (Petrol Station and Forecourt Shop)
A through the wall style cash machine in a steel housing: a blank screen, keypad, card slot and dispense tray under an accent head box, with a slatted security shutter that runs up into the head.