Free models · CC0
Stylized
Every modern model below is a self-contained .glb under 25 MB, released under CC0 1.0 so it can be used and modified in commercial projects without attribution.
Load one straight from its CDN URL with a plain GLTFLoader, or take a whole themed set from the packs.
747 free GLB models
Powder board with bindings (Backcountry Snowboarding and Avalanche Safety)
Directional 1.62 m powder board with a swallowtail, set back stance and two strap bindings fitted.
Splitboard in ride mode (Backcountry Snowboarding and Avalanche Safety)
Splitboard joined into one 1.58 m board with the centre seam, tip and tail clips and touring pucks visible.
Guide pointing out a line (Backcountry Snowboarding and Avalanche Safety)
Guide stopped on a safe island, one arm out calling the line, probe planted, transceiver worn on a chest harness.
Rider standing with the board upright (Backcountry Snowboarding and Avalanche Safety)
Rider standing in boots at the top of a line, holding the board upright on its tail beside them.
Rider digging a snow pit (Backcountry Snowboarding and Avalanche Safety)
Rider crouched at a pit face shovelling the wall back, spoil thrown out to the side.
Rider seated strapping in (Backcountry Snowboarding and Avalanche Safety)
Rider sitting in the snow with the board across in front, working an ankle ratchet, pack dumped alongside.
Splitboarder skinning uphill (Backcountry Snowboarding and Avalanche Safety)
Touring splitboarder mid stride on two split halves with skins fitted, poles planted, pack loaded for the day.
Rider airborne off a natural lip (Backcountry Snowboarding and Avalanche Safety)
Snowboarder in the air off a natural snow lip, knees tucked, front hand grabbing the heel edge between the bindings.
Rider crouched in powder (Backcountry Snowboarding and Avalanche Safety)
Snowboarder compressed low in deep snow on a swallowtail board, arms wide, bow wave rolling off the nose.
Rider carving a heelside turn (Backcountry Snowboarding and Avalanche Safety)
Snowboarder laid over on the heel edge mid turn, knees loaded, trailing hand near the snow, with thrown snow off the buried edge.
Apron And Belt Connector Cases (Airport Terminal and Ground Operations)
Composed example for Airport Terminal and Ground Operations.
Airfield Support Compound (Airport Terminal and Ground Operations)
Composed example for Airport Terminal and Ground Operations.
Stand Turnaround (Airport Terminal and Ground Operations)
Composed example for Airport Terminal and Ground Operations.
Departures Concourse (Airport Terminal and Ground Operations)
Composed example for Airport Terminal and Ground Operations.
AnimatedPerimeter Gate (Airport Terminal and Ground Operations)
Airside perimeter sliding gate: two capped portal posts on cast pads, a ground rail, a mesh gate leaf on a named sliding node with hazard panels and rollers, and a guard kiosk with a card reader and a camera mast.
Perimeter Fence Run (Airport Terminal and Ground Operations)
Eight metre airfield perimeter fence bay: three posts on cast pads carrying a mesh panel with vertical wires and three line rails, angled top arms with three strand wires and a blank warning plate.
Hangar Frontage (Airport Terminal and Ground Operations)
Maintenance hangar frontage: a gabled shed with a real bored door opening, six folding door leaves with glazed upper panels, a coloured header band, a threshold strip, side walls and a ribbed roof deck.
GSE Store (Airport Terminal and Ground Operations)
Ground equipment store: a three bay open-fronted shed on a paved slab, with piers between the bays, a mono-pitch ribbed roof with a coloured fascia and edge rail, racking along the back wall, bay markings and a wall display.
Crew Building (Airport Terminal and Ground Operations)
Two storey airside crew and operations building: a banded block with continuous window ribbons and mullions on both floors, a parapet, a canopied glazed entrance on a paved forecourt, a roof plant housing and mast aerials.
Control Tower (Airport Terminal and Ground Operations)
Airfield control tower: a two storey glazed base block with an entrance canopy, a tapered shaft carrying a spiral stair band, and an outward-raked glazed cab with mullions, a service gallery with railings, roof antennas and a mast light.
Marshalling Wand Pair (Airport Terminal and Ground Operations)
Marshalling wand pair in a charging cradle: two illuminated amber batons with dark grips standing in a weighted base with a status light, as they are left at the head of a stand.
Stand Guidance Display (Airport Terminal and Ground Operations)
Visual docking guidance display: a two post frame carrying a large dark alignment screen with a centre bar and closing-rate strip, a coloured header hood and a ground level operator panel.
Safety Cone Row (Airport Terminal and Ground Operations)
Airside cone row: five square-based traffic cones at 1.2 m centres with reflective collars and linking tapes, for closing a lane or fencing a spill on the apron.
Wheel Chock And Cone Set (Airport Terminal and Ground Operations)
Landing gear chock and cone set: a linked pair of moulded amber chocks with grip plates and a pull rope, and two square-based traffic cones with reflective collars, arranged as they are placed at a wheel.