Free models · CC0
Props
Every realistic prop below is a self-contained .glb under 5 MB, released under CC0 1.0 so it can be used and modified in commercial projects without attribution.
Load one straight from its CDN URL with a plain GLTFLoader, or take a whole props set from the packs.
2,495 free GLB models
Summit cairn (Mountaineering and Summit Expedition)
Stacked stone summit cairn about 1.2 m high with a wand and two strips of marker tape.
Stove and pot set (Mountaineering and Summit Expedition)
Gas cartridge stove with pot supports, a wide pot and lid, a wrapped windscreen and a spare cartridge.
Glacier goggles (Mountaineering and Summit Expedition)
Wide cylindrical-lens goggles in a foam-backed frame with an elasticated strap laid out behind.
High-altitude double boots (Mountaineering and Summit Expedition)
Pair of double boots with integral gaiters, front zips, lace hooks and welts for crampon bails.
Summit pack (Mountaineering and Summit Expedition)
Thirty litre lidless summit pack on the same back system, stripped for a summit day.
Climbing harness with rack (Mountaineering and Summit Expedition)
Padded sit harness on a stand, with four gear loops carrying karabiners, slings and a belay device.
Oxygen mask and regulator (Mountaineering and Summit Expedition)
Oro-nasal mask with an exhalation port and reservoir, on a corrugated hose to a regulator block.
Expedition pack (Mountaineering and Summit Expedition)
Seventy-five litre expedition pack with a lid, hip belt, compression straps, axe loops and a strapped rope.
Oxygen cylinder (Mountaineering and Summit Expedition)
Filament-wound oxygen cylinder with a neck valve, gauge, carry ring and a protective cage.
Climbing helmet (Mountaineering and Summit Expedition)
Hybrid shell climbing helmet with side vents, headlamp clips and an adjustable chin harness.
Coiled climbing rope (Mountaineering and Summit Expedition)
Sixty-metre single rope flaked into a butterfly coil, waist-wrapped and tied off with two tails.
Route marker wand line (Mountaineering and Summit Expedition)
Six route wands set out over seven metres, each with a flag panel and packed snow at the foot.
Haul bag (Mountaineering and Summit Expedition)
Reinforced cylindrical haul bag with a closure flap, four-point haul suspension and shoulder straps.
Fixed rope anchor on pickets (Mountaineering and Summit Expedition)
Three T-section snow pickets driven back and equalised to one master point carrying a fixed rope.
Camp table with stools (Mountaineering and Summit Expedition)
Folding alloy camp table with three tripod stools, a vacuum flask and two mugs.
Solar panel and battery box (Mountaineering and Summit Expedition)
Folding solar panel on an adjustable alloy A-frame with a cabled battery box.
Flag line on poles (Mountaineering and Summit Expedition)
Five-metre span of small cloth flags on a sagging line between two guyed poles braced by rock piles.
Supply cache under a tarp (Mountaineering and Summit Expedition)
Barrels under a lashed tarp weighted with rocks, with crates and a duffel stacked alongside.
Craft support cradle (UFO Crash Site and Recovery Facility)
A 9 m steel cradle holding a disc craft clear of the floor: four A-frame legs on concrete pads tied by a base ring and diagonal braces, four raked saddles with padded top plates and side stops, a hazard band and a four-tread access stair with rails.
Sample rack wall (UFO Crash Site and Recovery Facility)
A 2.4 by 2.3 m sample rack: six shelf levels carrying twenty four trays of capped vials, blank shelf labels and a closed top plate.
Analysis bench (UFO Crash Site and Recovery Facility)
A 2.8 m laboratory bench: a cupboard base with three drawer lines, a fume hood with a glass sash and extract duct over the left half, a reagent shelf, an instrument case, a microscope, four capped sample vials and two stools.
Control console bank (UFO Crash Site and Recovery Facility)
A five-position curved console bank on a 3.6 m radius: raked instrument panels with lit faces, upright screens, keyboard shelves, a cable tray under the desks and two five-star operator chairs.
Cryogenic pod (UFO Crash Site and Recovery Facility)
A 2.6 m cryogenic pod on a steel cradle at 9 degrees head-up: a rounded outer shell, a frosted lid on a hinged node, a foot-end compressor with coiled lines and two lit control panels.
Examination table (UFO Crash Site and Recovery Facility)
A 2.3 m stainless examination table on a pedestal column and ram: a dished top with side rails, a centre drain channel running to a floor sump, an articulated two-link overhead lamp on its own floor post and a three-shelf instrument trolley on castors.